Product Our Products

Fundamentals: Types of Copper and Properties

1.1. Types of Copper and Properties. The copper most commonly used for sheet and strip appli ions complies with ASTM B370. It consists of 99.9 percent copper, and is available in six tempers designated by ASTM B370 as: 060 soft , H00 cold rolled , H01 cold rolled, high yield , H02 half hard , H03 three quarter hard , and H04 hard .Coefficient of Thermal Expansion: 0.0000098/ 176F from 68 176F to 572 176F

NASA Systems Engineering Handbook

0183 32NASA/SP20076105 Rev1 Systems Engineering Handbook National Aeronautics and Space Administration NASA Headquarters Washington, D.C. 20546 December 2007

Dielectric Constant Table Honeywell Process

0183 3224/06/2011 0183 32design and apply instruments such as level controls ... Compound 3.6 Copper Catalyst 6.0 6.2 Copper Oleate 68 176 F 2.8 Copper Oxide 18.1 Corderite 2.5 5.4 Corn 510 Corn Dry Granulars 1.8 Page 11 6/24/2011. Dielectric Constant Table.xls Corn, Refuse 2.32.6 Corning Glass 6.5 Cotton 1.31.4 Cotton Seed Oil 3.1 Co2 32 176 F 1.6 ...

Pipe/Conduit Clamps and Hangers Eaton

0183 3217/04/2020 0183 32DCU DURACOPPER HDG ... Bolt Size 1/420 5 1618 3 816 213 ft.lbs 6 11 19 50 Nm 8 15 26 68 Eaton 168 BLine series strut systems. Pipe/Conduit Clamps and Hangers Reference page 168 for ... 114.3 27.5 12.5 A Design Load 4Dimension compatible fitting open side only OSO OSO OSO

Engineering Data for Copper and Aluminum Conductor ...

0183 32TABLE 1 2 Flexible Stranding 2 TABLE 1 3 Resistance in Ohms per 1000 feet per Conductor at 20 176C and 25 176C of solid wire and Class B Concentric Strands Copper and Aluminum Conductors 3 TABLE 1 4 Copper and Aluminum ResistanceTemperature Correction Factors 4 TABLE 1 5 AC/DC Resistance Ratios for Copper and Aluminum Conductors,

Magnetics Design 3 Windings

0183 32In copper at 100 176C, resistivity, p 2.3108 Qm, and r I: D PEN 7.67 cm.J7 copper At 100 kHz in copper, DpEN .024 cm. Proximity Effect When two conductors, thicker than DpEN, are in proximity and carry opposing currents, the high frequency current components spread across the surfaces

AN 114: Board Design Guidelines for Intel Programmable ...

0183 32design with Intel Programmable Devices. 1.2.1. Escape Routing. Escape routing is the method used to route each signal from a package to another element on the PCB. ... In an SMD pad, the solder mask overlaps the surface land pads copper surface. Refer to Figure 3 on page 6 for the Side View of NSMD and SMD Land Pads.

PCB Design Guidelines for 0.5mm PackageOnPackage PoP ...

0183 320.5mm pitch 0.65mm pitch Focus for Part II Memory Appli ions Processor Main PCB Part II PCB Design Scope of These Guidelines www.ti.com Figure 3. Focus for Part II PoP Assembly

ASME B31.3 Process Piping Guide Los Alamos National ...

0183 32The ASME B31.3 Code defines unlisted components as components not in Tables 326.1, A326.1, or K326.1. Unlisted components can have pressure ratings but the owner and/or the designer has the responsibility to verify that the design, materials, fabri ion, examination, and testing of the component meet the requirements of ASME B31.3.

ASME B31.3 Process Piping Guide Los Alamos National ...

0183 32LANL Engineering Standards Manual PD342 Chapter 17 Pressure Safety Section D20B31.3G, ASME B31.3 Process Piping Guide Rev. 2, 3/10/09 4 The Owner and Designer are responsible for compliance with the personnel and process qualifi ion requirements of the codes and standards. In particular, the appli ion of ASME B31.3 requires compliance with the Inspector qualifi ion